This sleek design allows the operator to flip this scope mount in either direction without blocking the ejection port. A favorite of Firearms Dealers as they do not have to carry 3-4 different models to fit different weapons platforms. Unlike our competitors (B&T / Brugger + Thomet / EOTech and others) our mount takes less than 3 minutes to mount on the weapon. Additionally we have ONE MOUNT THAT FITS ALL of the following Real World G3 / MP5 Hecker & Koch Weapons Systems.

WEAPONS SYSTEMS:

• HK 21
• HK 91
• HK G3 (All Variants)
• HK 33
• HK 53
• HK 93
• HK 94
• HK MP5A2 & MP5 A3
• HK MP5K
• HK MP5K PDW
• PTR-91 / JLD (All Variants)
• Vector 53 (All Variants)
• Special Weapons SW5 (All Variants)
• Bobcat Weapons BW-5 (All Variants)
• GSG5 .22 Cal. MP5 Clones

• As well as all Variants / Clones of MP5 & G3 World Wide; Licensed or Unlicensed i.e. Century, CITME, Greek, Iranian, Pakistani South African etc.

• NOTE: G3s with HK Ejection Port Buffers or any device that rolls over the top of the receiver in the same location as where the mount fits can NOT be used in tandem with our mount. The MFI Low Profile mount lays flat on top of the receiver with near ZERO clearance.

• 100% Made In the USA.

• 6061 T-6 Aircraft Grade Aluminum

• Patented Design: US 7,305,789

• CNC Machined

• Hard Anodized Flat Black

• Super Light Weight @ 71.0 gr. ( 2.535 oz. )

• 5.370 Inches ( 136.4mm ) Long.

• Super Low Profile Rail Height @ 0.295" ( 7.35mm ).

• 100% Picatinny / Mil. Spec. 1913 Correct.

• Tolerance held is + / - 0.001 (less than the thickness of a piece of paper).

• Near Zero Rise from the top of your receiver.

• 4 - Independent Draw Style Hooks for 100% Secure Attachment.

• 0.255 Inches (5.5mm) of Draw Length to accommodate even CITME / Out of Spec. Weapons.

• Chamfered Edges for Fast / Easy On & Off in Adverse Conditions.

• Added Stabilizing Point at the Far End. This keeps a solid contact between the top of your receiver and the scope mount.

• 3 - Counter Recoil Slots to Mate with your Specific Weapon's Scope Mount Anti-Recoil Blocks.

• Custom Length / Design / One Off / Prototypes Available. (See Below / Click Here)

• Does NOT Interfere with the iron sights when a scope is not in place. Clear unobstructed view over the rail.

MFI is the GENUINE ARTICLE / REAL DEAL that others copy from. This is the lowest profile mount available on the market. Designed for MP5 or any G3 variant to mount either Red Dots / Aim Points or Conventional Scopes. By far the Most Cost Effective WITHOUT Sacrificing Quality HK Scope Mount on the market.

Note that the attachment mechanism is NOT a quick release style like found on the original HK mounts. We thought about using some sort of quick release but, as we have heard that the Original HK Mount in a tactical situation has been known to un-lock if you accidentally hit that paddle lever. It does take a little more time to mount these (2-3 minutes) but, once they are in place they will never accidentally un-lock. Not even a hammer will jar our mount from it's zero.

Additionally we made these with the LOWEST PROFILE possible so that they do NOT interfere with the open / iron sites when a scope is not in place. The profile is so low that there is no reason to remove the mount once it has been attached to the weapon system as it does not interfere with any normal function or cleaning. A customer can have the ability to see through / under the scope (like the HK High Mount) if they just use medium to high profile scope rings with see through apertures. These were specifically designed to accommodate Aim Points and other Red Dot Sites.

Lastly: 100% Picatinny / Mil. Spec. 1913 Correct. Meaning that your expensive SWAN Throw Lever / Quick Release / ARMS Scope Rail Mount will lock 100% the way it was intended. We have seen the influx of hundreds foreign made mounts, rings, risers, rails etc. that claim to be Throw Lever compatible but, are NOT. This one is 100% COMPATIBLE!

TRUST YOUR LIFE TO QUALITY... NOT LOWEST PRICE!

SPECIAL NOTE ON CUSTOM MANUFACTURING: As mentioned above we make these here in the USA so we can custom manufacture any length / configuration you may need for your specific application. Meaning if you have a MP5 that you want a mount that has extended length in both directions we CAN accommodate you. One off versions / Prototypes are welcome as well as small quantities. We do this specifically as we have many requests from Real World Operators who require Real World Tactical Solutions.

• 1 - Unit / Prototype @ $575.00
• 5+ Units @ $350.00 per unit.
• 25+ Units @ $200.00 per unit.
• 100+ Units @ $150.00 per unit.
• 500+ Units @ $95.00 per unit.
• 1000+ Units @ P.O.R.
• 5000+ Units @ P.O.R.
• 10,000+ Units @ P.O.R.
• 50,000+ Units @ P.O.R.

The above custom prices are 100% prepaid in full. No return or exchange as it is your design. 10-12 week lead time.

INSTRUCTIONS FOR MOUNTING:

1. Be sure the weapon is unloaded and the safety is on.

2. Remove all 4 of the small bolts from the mount.

3. Open / pull outward the bottom of the hook / lock point on all 4 points.

4. Place the mount on top of the weapon's scope mounting points and press down. While pressure is applied press the mounting points back inward toward the receiver.

5. Place the small bolts back into the 4 holes and down into the mounting points and tighten by hand to avoid cross threading. Alternate from bolt to bolt as you tighten to keep the mount level. Use a 5/64 allen key / hex wrench to finish tightening (do not over tighten). The mount is now installed. To remove simply reverse the aforementioned instructions.

   The set screw is used to apply pressure down on to the top of the receiver to add stability to the extension area.

   Once attached to the weapon this mount should NOT be removed. It does NOT interfere with the iron sites or any other operation such as cleaning. On and Off removal will result in stripping the threads on the hooks.

SPECIAL NOTE on HK MP5, SP-89 and Clone HK 94s: The recoil stop block on all MP5 variants is a separate welded on part. This notice does NOT effect any G3 / 91 or HK33 / HK 93 variants as this same block is pressed into the receiver. The MFI HK Low Profile mount does NOT require any modification or hand fitting. Any mounting issues due to out of spec. receivers recoil stop block weld points should be addressed to MFI immediately for an exchange. Our latest version has special relief cuts / channels to accommodate even the worsted receiver welding job. We have only seen issues like this on less than 1% of our sales.

We do NOT accept exchanges on modified mounts or on counterfeit / copies of our product.